KC-2
KC-3
KC-4
KC-5
KC-1
KC-1
KC-6 REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.001
KC-6 (REPLACEMENT TYPE)
KC-6
KCW-2
KCW-3
KCW-4
KCW-5

KCW-1
KCW-1

　KABUTO SEAL CENTER

S-S KS-P
KS-S KS-P

KS-2Sor2P
KS-3Sor3P
KS-4Sor4P
KS-5Sor5P

KS-A
KS-A

 KS-3A

KS-4A
KS-5A

KS-B
KS-B

KS-3B
KS-4B
KS-5B

KS　KABUTO SEAL CENTER
n.

KS-S KS-P
KS-S KS-P

KS-2Sor2P
KS-3Sor3P
KS-4Sor4P
KS-5Sor5P
KS-A
KS-A

KS-3A
KS-4A
KS-5A

KS-B
KS-B
KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7
KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10
KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14

KFL　KABUTO FINELIVE CENTER

KFL
KFL

KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200
KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100
KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600

KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-A

KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12
KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14
KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18

KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-B

KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7
KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10
KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14

KFL　KABUTO FINELIVE CENTER

KFL REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003
KFL

KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200
KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100
KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600
KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-A

KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12
KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14
KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18

KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-B

KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7
KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10
KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14

KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200
KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100
KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600

KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-A

KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12
KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14
KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18

KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFL-B

KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7
KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10
KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14

KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003
KSN
(g)
KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950
KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820
KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160

KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KSN-A
KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12
KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14
KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18

KSN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KSN-B
KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7
KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10
KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14

KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003
KSN
KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950
KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820
KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160

KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KSN-A
KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12
KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14
KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18

KSN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KSN-B

KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7
KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10
KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14

KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003
KSN

KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950
KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820
KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160

KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KSN-A

KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12
KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14
KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18

KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7
KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10
KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14

KFN　KABUTO FINELIVE CENTER with NUT

KFN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003
KFN
KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240
KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330
KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150

KFN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFN-A

KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12
KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14
KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18

KFN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFN-B
KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7
KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10
KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14

KFN　KABUTO FINELIVE CENTER with NUT

KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240
KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330
KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150
KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12
KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14
KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18

KFN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KFN-B

KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7
KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10
KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14

KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240
KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330
KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150
3
KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12
KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14
KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18
41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7
KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10
KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14

KLN　KABUTO LATHE CENTER with NUT
F L M N N1 H WEIGHT (g)
KLN-3 No.3 24 16 36.1 11 87.5 6.5 22.4 134.6 M26×P1.5 41 13 21 590
KLN-4 No.4 32 16 36.2 15 112.5 10 22.5 163.7 M36×P1.5 55 22 27 1,230
KLN-5 No.5 44 26 61.2 15.5 141.5 10 38 218.2 M50×P1.5 69 20 36 2,560

KLN　KABUTO LATHE CENTER with NUT

KLN REPLACEMENT TYPE WAGGLE ACCURACY 0.005
KLN
KLN-3 No.3 24 16 36.1 11 87.5 6.5 22.4 134.6 M26×P1.5 41 13 21 590
KLN-4 No.4 32 16 36.2 15 112.5 10 22.5 163.7 M36×P1.5 55 22 27 1,230
KLN-5 No.5 44 26 61.2 15.5 141.5 10 38 218.2 M50×P1.5 69 20 36 2,560

KS-S KS-P REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY S TYPE 0.006 P TYPE 0.003
KS-S KS-P
KS-2Sor2P No.2 37 27 15.5 36.2 30 68 4 22.5 134.2 REPLACEMENT 500
KS-3Sor3P No.3 44 30 16 36.2 42 85 4.5 22.5 163.2 REPLACEMENT 860
KS-4Sor4P No.4 56 32 16 36.2 54 108 5.3 22.5 198.2 REPLACEMENT 1,700
KS-5Sor5P No.5 73 52 26 60.5 66 136 6.3 38 262.5 REPLACEMENT 3,900

KS-3A No.3 44 26 34 42 85 4.5 161 INTEGRAL 850 φ12
KS-4A No.4 56 32 41 54 108 5.3 203 INTEGRAL 1,750 φ14
KS-5A No.5 73 40 48 66 136 6.3 250 INTEGRAL 3,650 φ18

KS-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003
KS-B

*For KS-A, B, please choose steel (tempered product) or with carbide.
(UNIT mm)
KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7
KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10
KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14

KABUTO CLIPPER
Easy-to-handle lathe optimal for grinding and machining shafts.
Uses the eccentric cam.

KABUTO CLIPPER
Easily detachable in one hand.
Not slippery as it is more firmly fastened under larger load.
The finished work surface is less likely to be scratched as it is pressed in a planar manner.
DIMENSIONS TABLE
(UNIT mm)
MODEL TYPE RANGE OF USE A B C D E G (BOLT) SPRING WEIGHT (g)
#8 φ4～φ8 26 12 51 6.3 3.2 M4 P0.7×20 SMALL 40
#13 φ6～φ14 36 18 72 11 4.3 M6 P1.0×25 LARGE 100
#22 φ13～φ24 48 28 88 11 4.3 M6 P1.0×25 LARGE 130
#30 φ20～φ33 58 38 94 11 4.3 M6 P1.0×25 LARGE 160
#40 φ31～φ42 68 48 103 11 4.3 M6 P1.0×25 LARGE 190
#50S φ38～φ50 78 58 115 11 4.3 M6 P1.0×30 LARGE 250
#60S φ47～φ62 95 70 134 14 6 M8 P1.25×40 NEW OVERSIZE 450
#80S φ60～φ80 115 90 155 14 6 M8 P1.25×40 NEW OVERSIZE 540
#100 φ80～φ100 140 109 189 20 9 M10 P1.5×45 OVERSIZE 1,100
Specialty #4 φ2～φ4 22 8.5 45 6 3.2 M4 P0.7×20 SMALL -
Specialty #120 φ100～φ120 164 132 209 20 9 M10 P1.5×45 OVERSIZE -
*Dimensions are subject to change for alteration without prior notice.

KC　KABUTO CENTER

Regular model for general lathe.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KC is not waterproof.
• Type KC comes with the center head A and then the center head ejecting drift DHN-1
  (KC-5 come with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)	HEAD ANGLE
KC-2	No.2	35	27	15.5	36.2	32	68	4	22.5	136.2	REPLACEMENT	510	60°
KC-3	No.3	40	30	16	36.2	37.5	85	4.5	22.5	158.7	REPLACEMENT	780	60°
KC-4	No.4	49.5	32	16	36.2	47	108	5.3	22.5	191.2	REPLACEMENT	1,400	60°
KC-5	No.5	68	52	26	60.5	57	136	6.3	38	253.5	REPLACEMENT	3,600	60°

*Dimensions are subject to change for alteration without prior notice.

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	HEAD ANGLE
KC-1	No.1	23.5	16	18.5	23.5	57	3.5	99	INTEGRAL	160	60°

*Dimensions are subject to change for alteration without prior notice.

• Type KC-6 comes with the center head 6A60° and then the center head ejecting drift DHN-2.

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KC-6	No.6	125	65	33	70.5	87	189	8	44	346.5	REPLACEMENT	15,000

●Only KC-6 is waterproof and dust proof with taper roller bearing.
(With nut is available so please contact us for details.)

*Dimensions are subject to change for alteration without prior notice.

• Head angles available are: 60°, 75° and 90°.

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	HEAD ANGLE
KC-6	No.6	125	65	31	70.5	87	189	8	346.5	INTEGRAL	15,000	60°
	No.6	125	65	31	57	87	189	8	333	INTEGRAL	15,000	75°
	No.6	125	65	31	48	87	189	8	324	INTEGRAL	15,000	90°

●Only KC-6 is waterproof and dust proof with taper roller bearing.
(With nut is available so please contact us for details.)

The KCW series has been out of print.
We will terminate sales as soon as stock runs out.

KCW　KABUTO CENTER DOUBLE CAP

Simple waterproof version of type KC suitable
for the general lathe that uses cutting water.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• We recommend that type KS or KFL be used for the NC lathe.
• Type KCW comes with the center head A and then the center head ejecting drift DHN-1
  (KCW-5 come with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	B1	C	E	F	L	HEAD TYPE	WEIGHT (g)
KCW-2	No.2	37	35	27	15.5	36.2	32	11.5	68	4	22.5	136.2	REPLACEMENT	530
KCW-3	No.3	42	40	30	16	36.2	37.5	16	85	4.5	22.5	158.7	REPLACEMENT	800
KCW-4	No.4	52	49.5	32	16	36.2	47	18.5	108	5.3	22.5	191.2	REPLACEMENT	1,450
KCW-5	No.5	69.5	68	52	26	60.5	57	23	136	6.3	38	253.5	REPLACEMENT	3,650

*Dimensions are subject to change for alteration without prior notice.

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	A	B	B1	C	E	L	HEAD TYPE	WEIGHT (g)
KCW-1	No.1	25	23.5	16	18.5	23.5	8.5	57	3.5	99	INTEGRAL	170

*Dimensions are subject to change for alteration without prior notice.

KS　KABUTO SEAL CENTER

Structured to keep cutting water away by means of oil seal.
The waterproofing function still works under slower rotation.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• The difference between types S and P is their waggle accuracy.
• We recommend that type KFL be used for fine machining or light metal working.
• Types S and P have the same dimensions.
• Type KS comes with the center head A and then the center head ejecting drift DHN-1
  (KS-5S and P come with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KS-2Sor2P	No.2	37	27	15.5	36.2	30	68	4	22.5	134.2	REPLACEMENT	500
KS-3Sor3P	No.3	44	30	16	36.2	42	85	4.5	22.5	163.2	REPLACEMENT	860
KS-4Sor4P	No.4	56	32	16	36.2	54	108	5.3	22.5	198.2	REPLACEMENT	1,700
KS-5Sor5P	No.5	73	52	26	60.5	66	136	6.3	38	262.5	REPLACEMENT	3,900

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KS-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KS-3A	No.3	44	26	34	42	85	4.5	161	INTEGRAL	850	φ12
KS-4A	No.4	56	32	41	54	108	5.3	203	INTEGRAL	1,750	φ14
KS-5A	No.5	73	40	48	66	136	6.3	250	INTEGRAL	3,650	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KS-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KS-3B	No.3	44	22	10	36	42	85	4.5	163	INTEGRAL	830	φ7
KS-4B	No.4	56	30	12	49	54	108	5.3	211	INTEGRAL	1,700	φ10
KS-5B	No.5	73	38	18	59	66	136	6.3	261	INTEGRAL	3,650	φ14

*Dimensions are subject to change for alteration without prior notice.

KS　KABUTO SEAL CENTER

Structured to keep cutting water away by means of oil seal.
The waterproofing function still works under slower rotation.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• The difference between types S and P is their waggle accuracy.
• We recommend that type KFL be used for fine machining or light metal working.
• Types S and P have the same dimensions.
• Type KS comes with the center head A and then the center head ejecting drift DHN-1
  (KS-5S and P come with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KS-2Sor2P	No.2	37	27	15.5	36.2	30	68	4	22.5	134.2	REPLACEMENT	500
KS-3Sor3P	No.3	44	30	16	36.2	42	85	4.5	22.5	163.2	REPLACEMENT	860
KS-4Sor4P	No.4	56	32	16	36.2	54	108	5.3	22.5	198.2	REPLACEMENT	1,700
KS-5Sor5P	No.5	73	52	26	60.5	66	136	6.3	38	262.5	REPLACEMENT	3,900

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KS-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KS-3A	No.3	44	26	34	42	85	4.5	161	INTEGRAL	850	φ12
KS-4A	No.4	56	32	41	54	108	5.3	203	INTEGRAL	1,750	φ14
KS-5A	No.5	73	40	48	66	136	6.3	250	INTEGRAL	3,650	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KS-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KS-3B	No.3	44	22	10	36	42	85	4.5	163	INTEGRAL	830	φ7
KS-4B	No.4	56	30	12	49	54	108	5.3	211	INTEGRAL	1,700	φ10
KS-5B	No.5	73	38	18	59	66	136	6.3	261	INTEGRAL	3,650	φ14

*Dimensions are subject to change for alteration without prior notice.

KFL　KABUTO FINELIVE CENTER

Structured to keep cutting water away by means of air film resulting from rotation.
The product with light running torque is most suitable
for fine machining or light metal working.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1
  (while KFL-5 comes with the carbide center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KFL-3	No.3	48	30	16	36.2	33	87	4.5	22.5	156.2	REPLACEMENT	1,200
KFL-4	No.4	63	32	16	40.2	42	109	5.3	26.5	191.2	REPLACEMENT	2,100
KFL-5	No.5	85	52	26	60.5	50	136	6.3	38	246.5	REPLACEMENT	4,600

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3A	No.3	48	28	37	33	87	4.5	157	INTEGRAL	1,200	φ12
KFL-4A	No.4	63	32	40	42	109	5.3	191	INTEGRAL	2,100	φ14
KFL-5A	No.5	85	42	55	50	136	6.3	241	INTEGRAL	4,600	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3B	No.3	48	25	10	41.5	33	87	4.5	161.5	INTEGRAL	1,150	φ7
KFL-4B	No.4	63	32	12	52	42	109	5.3	203	INTEGRAL	2,050	φ10
KFL-5B	No.5	85	42	20	65	50	136	6.3	251	INTEGRAL	4,500	φ14

*Dimensions are subject to change for alteration without prior notice.

KFL　KABUTO FINELIVE CENTER

Structured to keep cutting water away by means of air film resulting from rotation.
The product with light running torque is most suitable
for fine machining or light metal working.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1
  (while KFL-5 comes with the carbide center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KFL-3	No.3	48	30	16	36.2	33	87	4.5	22.5	156.2	REPLACEMENT	1,200
KFL-4	No.4	63	32	16	40.2	42	109	5.3	26.5	191.2	REPLACEMENT	2,100
KFL-5	No.5	85	52	26	60.5	50	136	6.3	38	246.5	REPLACEMENT	4,600

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3A	No.3	48	28	37	33	87	4.5	157	INTEGRAL	1,200	φ12
KFL-4A	No.4	63	32	40	42	109	5.3	191	INTEGRAL	2,100	φ14
KFL-5A	No.5	85	42	55	50	136	6.3	241	INTEGRAL	4,600	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3B	No.3	48	25	10	41.5	33	87	4.5	161.5	INTEGRAL	1,150	φ7
KFL-4B	No.4	63	32	12	52	42	109	5.3	203	INTEGRAL	2,050	φ10
KFL-5B	No.5	85	42	20	65	50	136	6.3	251	INTEGRAL	4,500	φ14

*Dimensions are subject to change for alteration without prior notice.

KFL　KABUTO FINELIVE CENTER

Structured to keep cutting water away by means of air film resulting from rotation.
The product with light running torque is most suitable
for fine machining or light metal working.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1
  (while KFL-5 comes with the carbide center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	F	L	HEAD TYPE	WEIGHT (g)
KFL-3	No.3	48	30	16	36.2	33	87	4.5	22.5	156.2	REPLACEMENT	1,200
KFL-4	No.4	63	32	16	40.2	42	109	5.3	26.5	191.2	REPLACEMENT	2,100
KFL-5	No.5	85	52	26	60.5	50	136	6.3	38	246.5	REPLACEMENT	4,600

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3A	No.3	48	28	37	33	87	4.5	157	INTEGRAL	1,200	φ12
KFL-4A	No.4	63	32	40	42	109	5.3	191	INTEGRAL	2,100	φ14
KFL-5A	No.5	85	42	55	50	136	6.3	241	INTEGRAL	4,600	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFL-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD	φd	φh	A	B	C	E	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFL-3B	No.3	48	25	10	41.5	33	87	4.5	161.5	INTEGRAL	1,150	φ7
KFL-4B	No.4	63	32	12	52	42	109	5.3	203	INTEGRAL	2,050	φ10
KFL-5B	No.5	85	42	20	65	50	136	6.3	251	INTEGRAL	4,500	φ14

*Dimensions are subject to change for alteration without prior notice.

KSN　KABUTO SEAL CENTER with NUT

Structured to keep cutting water away by means of oil seal.
The waterproofing function still works under slower rotation.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KSN has the same waterproof structure as that of type KS.
• We recommend that type KFN be used for fine machining or light metal working.
• Type KSN comes with the center head A and then the center head ejecting drift DHN-1
  (while KSN-5 comes with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	F	J	L	HEAD TYPE	WEIGHT (g)
KSN-3	No.3	54	44	30	16	36.2	45	82	1.5	22.5	33	163.2	REPLACEMENT	950
KSN-4	No.4	69	56	32	16	36.2	57.5	104.5	1.8	22.5	43.5	198.2	REPLACEMENT	1,820
KSN-5	No.5	88	73	52	26	60.5	70	132	2.3	38	54	262.5	REPLACEMENT	4,160

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3A	No.3	54	44	26	34	45	82	1.5	33	161	INTEGRAL	930	φ12
KSN-4A	No.4	69	56	32	41	57.5	104.5	1.8	43.5	203	INTEGRAL	1,880	φ14
KSN-5A	No.5	88	73	40	48	70	132	2.3	54	250	INTEGRAL	3,950	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3B	No.3	54	44	22	10	36	45	82	1.5	33	163	INTEGRAL	890	φ7
KSN-4B	No.4	69	56	30	12	49	57.5	104.5	1.8	43.5	211	INTEGRAL	1,860	φ10
KSN-5B	No.5	88	73	38	18	59	70	132	2.3	54	261	INTEGRAL	3,950	φ14

*Dimensions are subject to change for alteration without prior notice.

KSN　KABUTO SEAL CENTER with NUT

Structured to keep cutting water away by means of oil seal.
The waterproofing function still works under slower rotation.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KSN has the same waterproof structure as that of type KS.
• We recommend that type KFN be used for fine machining or light metal working.
• Type KSN comes with the center head A and then the center head ejecting drift DHN-1
  (while KSN-5 comes with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	F	J	L	HEAD TYPE	WEIGHT (g)
KSN-3	No.3	54	44	30	16	36.2	45	82	1.5	22.5	33	163.2	REPLACEMENT	950
KSN-4	No.4	69	56	32	16	36.2	57.5	104.5	1.8	22.5	43.5	198.2	REPLACEMENT	1,820
KSN-5	No.5	88	73	52	26	60.5	70	132	2.3	38	54	262.5	REPLACEMENT	4,160

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3A	No.3	54	44	26	34	45	82	1.5	33	161	INTEGRAL	930	φ12
KSN-4A	No.4	69	56	32	41	57.5	104.5	1.8	43.5	203	INTEGRAL	1,880	φ14
KSN-5A	No.5	88	73	40	48	70	132	2.3	54	250	INTEGRAL	3,950	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3B	No.3	54	44	22	10	36	45	82	1.5	33	163	INTEGRAL	890	φ7
KSN-4B	No.4	69	56	30	12	49	57.5	104.5	1.8	43.5	211	INTEGRAL	1,860	φ10
KSN-5B	No.5	88	73	38	18	59	70	132	2.3	54	261	INTEGRAL	3,950	φ14

*Dimensions are subject to change for alteration without prior notice.

KSN　KABUTO SEAL CENTER with NUT

Structured to keep cutting water away by means of oil seal.
The waterproofing function still works under slower rotation.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KSN has the same waterproof structure as that of type KS.
• We recommend that type KFN be used for fine machining or light metal working.
• Type KSN comes with the center head A and then the center head ejecting drift DHN-1
  (while KSN-5 comes with the center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	F	J	L	HEAD TYPE	WEIGHT (g)
KSN-3	No.3	54	44	30	16	36.2	45	82	1.5	22.5	33	163.2	REPLACEMENT	950
KSN-4	No.4	69	56	32	16	36.2	57.5	104.5	1.8	22.5	43.5	198.2	REPLACEMENT	1,820
KSN-5	No.5	88	73	52	26	60.5	70	132	2.3	38	54	262.5	REPLACEMENT	4,160

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3A	No.3	54	44	26	34	45	82	1.5	33	161	INTEGRAL	930	φ12
KSN-4A	No.4	69	56	32	41	57.5	104.5	1.8	43.5	203	INTEGRAL	1,880	φ14
KSN-5A	No.5	88	73	40	48	70	132	2.3	54	250	INTEGRAL	3,950	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KSN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KSN-3B	No.3	54	44	22	10	36	45	82	1.5	33	163	INTEGRAL	890	φ7
KSN-4B	No.4	69	56	30	12	49	57.5	104.5	1.8	43.5	211	INTEGRAL	1,860	φ10
KSN-5B	No.5	88	73	38	18	59	70	132	2.3	54	261	INTEGRAL	3,950	φ14

*Dimensions are subject to change for alteration without prior notice.

KFN　KABUTO FINELIVE CENTER with NUT

Structured to keep cutting water away
by means of air film resulting from rotation.
The product with light running torque is most suitable
for fine machining or light metal working.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KFN has the same waterproof structure as that of type KFL.
• Type KFN comes with the carbide center head A and then the center head ejecting drift DHN-1
  (while KFN-5 comes with the carbide center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	F	J	L	HEAD TYPE	WEIGHT (g)
KFN-3	No.3	60	48	30	16	36.2	36	84	1.5	22.5	24	156.2	REPLACEMENT	1,240
KFN-4	No.4	79	63	32	16	40.2	45.5	105.5	1.8	26.5	31.5	191.2	REPLACEMENT	2,330
KFN-5	No.5	105	85	52	26	60.5	54	132	2.3	38	37	246.5	REPLACEMENT	5,150

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFN-3A	No.3	60	48	28	37	36	84	1.5	24	157	INTEGRAL	1,280	φ12
KFN-4A	No.4	79	63	32	40	45.5	105.5	1.8	31.5	191	INTEGRAL	2,440	φ14
KFN-5A	No.5	105	85	42	55	54	132	2.3	37	241	INTEGRAL	5,080	φ18

*Dimensions are subject to change for alteration without prior notice.

• The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

DIMENSIONS TABLE

 

*For KFN-A, B, please choose steel (tempered product) or with carbide.

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	J	L	HEAD TYPE	WEIGHT (g)	CARBIDE DIAMETER
KFN-3B	No.3	60	48	25	10	41.5	36	84	1.5	24	161.5	INTEGRAL	1,180	φ7
KFN-4B	No.4	79	63	32	12	52	45.5	105.5	1.8	31.5	203	INTEGRAL	2,410	φ10
KFN-5B	No.5	105	85	42	20	65	54	132	2.3	37	251	INTEGRAL	5,120	φ14

*Dimensions are subject to change for alteration without prior notice.

KFN　KABUTO FINELIVE CENTER with NUT

Structured to keep cutting water away
by means of air film resulting from rotation.
The product with light running torque is most suitable
for fine machining or light metal working.
The replacement head enables cost reduction.

• See page HEAD LIST for center head types.
• See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute.
• Type KFN has the same waterproof structure as that of type KFL.
• Type KFN comes with the carbide center head A and then the center head ejecting drift DHN-1
  (while KFN-5 comes with the carbide center head 5A60° and DHN-2).

DIMENSIONS TABLE

(UNIT mm)

MODEL TYPE	M.T.	φD1	φD	φd	φh	A	B	C	E	F	J	L	HEAD TYPE	WEIGHT (g)
KFN-3	No.3	60	48< KC　KABUTO CENTER Regular model for general lathe. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KC is not waterproof. Type KC comes with the center head A and then the center head ejecting drift DHN-1 (KC-5 come with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) HEAD ANGLE KC-2 No.2 35 27 15.5 36.2 32 68 4 22.5 136.2 REPLACEMENT 510 60° KC-3 No.3 40 30 16 36.2 37.5 85 4.5 22.5 158.7 REPLACEMENT 780 60° KC-4 No.4 49.5 32 16 36.2 47 108 5.3 22.5 191.2 REPLACEMENT 1,400 60° KC-5 No.5 68 52 26 60.5 57 136 6.3 38 253.5 REPLACEMENT 3,600 60° *Dimensions are subject to change for alteration without prior notice. DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) HEAD ANGLE KC-1 No.1 23.5 16 18.5 23.5 57 3.5 99 INTEGRAL 160 60° *Dimensions are subject to change for alteration without prior notice. Type KC-6 comes with the center head 6A60° and then the center head ejecting drift DHN-2. DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KC-6 No.6 125 65 33 70.5 87 189 8 44 346.5 REPLACEMENT 15,000 ●Only KC-6 is waterproof and dust proof with taper roller bearing. (With nut is available so please contact us for details.) *Dimensions are subject to change for alteration without prior notice. Head angles available are: 60°, 75° and 90°. DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) HEAD ANGLE KC-6 No.6 125 65 31 70.5 87 189 8 346.5 INTEGRAL 15,000 60° No.6 125 65 31 57 87 189 8 333 INTEGRAL 15,000 75° No.6 125 65 31 48 87 189 8 324 INTEGRAL 15,000 90° ●Only KC-6 is waterproof and dust proof with taper roller bearing. (With nut is available so please contact us for details.) The KCW series has been out of print. We will terminate sales as soon as stock runs out. KCW　KABUTO CENTER DOUBLE CAP Simple waterproof version of type KC suitable for the general lathe that uses cutting water. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. We recommend that type KS or KFL be used for the NC lathe. Type KCW comes with the center head A and then the center head ejecting drift DHN-1 (KCW-5 come with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B B1 C E F L HEAD TYPE WEIGHT (g) KCW-2 No.2 37 35 27 15.5 36.2 32 11.5 68 4 22.5 136.2 REPLACEMENT 530 KCW-3 No.3 42 40 30 16 36.2 37.5 16 85 4.5 22.5 158.7 REPLACEMENT 800 KCW-4 No.4 52 49.5 32 16 36.2 47 18.5 108 5.3 22.5 191.2 REPLACEMENT 1,450 KCW-5 No.5 69.5 68 52 26 60.5 57 23 136 6.3 38 253.5 REPLACEMENT 3,650 *Dimensions are subject to change for alteration without prior notice. DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd A B B1 C E L HEAD TYPE WEIGHT (g) KCW-1 No.1 25 23.5 16 18.5 23.5 8.5 57 3.5 99 INTEGRAL 170 *Dimensions are subject to change for alteration without prior notice. KS　KABUTO SEAL CENTER Structured to keep cutting water away by means of oil seal. The waterproofing function still works under slower rotation. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. The difference between types S and P is their waggle accuracy. We recommend that type KFL be used for fine machining or light metal working. Types S and P have the same dimensions. Type KS comes with the center head A and then the center head ejecting drift DHN-1 (KS-5S and P come with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KS-2Sor2P No.2 37 27 15.5 36.2 30 68 4 22.5 134.2 REPLACEMENT 500 KS-3Sor3P No.3 44 30 16 36.2 42 85 4.5 22.5 163.2 REPLACEMENT 860 KS-4Sor4P No.4 56 32 16 36.2 54 108 5.3 22.5 198.2 REPLACEMENT 1,700 KS-5Sor5P No.5 73 52 26 60.5 66 136 6.3 38 262.5 REPLACEMENT 3,900 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KS-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KS-3A No.3 44 26 34 42 85 4.5 161 INTEGRAL 850 φ12 KS-4A No.4 56 32 41 54 108 5.3 203 INTEGRAL 1,750 φ14 KS-5A No.5 73 40 48 66 136 6.3 250 INTEGRAL 3,650 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KS-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7 KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10 KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14 *Dimensions are subject to change for alteration without prior notice. KS　KABUTO SEAL CENTER Structured to keep cutting water away by means of oil seal. The waterproofing function still works under slower rotation. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. The difference between types S and P is their waggle accuracy. We recommend that type KFL be used for fine machining or light metal working. Types S and P have the same dimensions. Type KS comes with the center head A and then the center head ejecting drift DHN-1 (KS-5S and P come with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KS-2Sor2P No.2 37 27 15.5 36.2 30 68 4 22.5 134.2 REPLACEMENT 500 KS-3Sor3P No.3 44 30 16 36.2 42 85 4.5 22.5 163.2 REPLACEMENT 860 KS-4Sor4P No.4 56 32 16 36.2 54 108 5.3 22.5 198.2 REPLACEMENT 1,700 KS-5Sor5P No.5 73 52 26 60.5 66 136 6.3 38 262.5 REPLACEMENT 3,900 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KS-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KS-3A No.3 44 26 34 42 85 4.5 161 INTEGRAL 850 φ12 KS-4A No.4 56 32 41 54 108 5.3 203 INTEGRAL 1,750 φ14 KS-5A No.5 73 40 48 66 136 6.3 250 INTEGRAL 3,650 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KS-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7 KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10 KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14 *Dimensions are subject to change for alteration without prior notice. KFL　KABUTO FINELIVE CENTER Structured to keep cutting water away by means of air film resulting from rotation. The product with light running torque is most suitable for fine machining or light metal working. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1 (while KFL-5 comes with the carbide center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 *Dimensions are subject to change for alteration without prior notice. KFL　KABUTO FINELIVE CENTER Structured to keep cutting water away by means of air film resulting from rotation. The product with light running torque is most suitable for fine machining or light metal working. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1 (while KFL-5 comes with the carbide center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 *Dimensions are subject to change for alteration without prior notice. KFL　KABUTO FINELIVE CENTER Structured to keep cutting water away by means of air film resulting from rotation. The product with light running torque is most suitable for fine machining or light metal working. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KFL comes with the carbide center head A and then the center head ejecting drift DHN-1 (while KFL-5 comes with the carbide center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E F L HEAD TYPE WEIGHT (g) KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFL-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD φd φh A B C E L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 *Dimensions are subject to change for alteration without prior notice. KSN　KABUTO SEAL CENTER with NUT Structured to keep cutting water away by means of oil seal. The waterproofing function still works under slower rotation. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KSN has the same waterproof structure as that of type KS. We recommend that type KFN be used for fine machining or light metal working. Type KSN comes with the center head A and then the center head ejecting drift DHN-1 (while KSN-5 comes with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g) KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 *Dimensions are subject to change for alteration without prior notice. KSN　KABUTO SEAL CENTER with NUT Structured to keep cutting water away by means of oil seal. The waterproofing function still works under slower rotation. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KSN has the same waterproof structure as that of type KS. We recommend that type KFN be used for fine machining or light metal working. Type KSN comes with the center head A and then the center head ejecting drift DHN-1 (while KSN-5 comes with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g) KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 *Dimensions are subject to change for alteration without prior notice. KSN　KABUTO SEAL CENTER with NUT Structured to keep cutting water away by means of oil seal. The waterproofing function still works under slower rotation. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KSN has the same waterproof structure as that of type KS. We recommend that type KFN be used for fine machining or light metal working. Type KSN comes with the center head A and then the center head ejecting drift DHN-1 (while KSN-5 comes with the center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g) KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KSN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 *Dimensions are subject to change for alteration without prior notice. KFN　KABUTO FINELIVE CENTER with NUT Structured to keep cutting water away by means of air film resulting from rotation. The product with light running torque is most suitable for fine machining or light metal working. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KFN has the same waterproof structure as that of type KFL. Type KFN comes with the carbide center head A and then the center head ejecting drift DHN-1 (while KFN-5 comes with the carbide center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g) KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240 KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330 KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12 KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14 KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18 *Dimensions are subject to change for alteration without prior notice. The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available. DIMENSIONS TABLE   *For KFN-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7 KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10 KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14 *Dimensions are subject to change for alteration without prior notice. KFN　KABUTO FINELIVE CENTER with NUT Structured to keep cutting water away by means of air film resulting from rotation. The product with light running torque is most suitable for fine machining or light metal working. The replacement head enables cost reduction. See page HEAD LIST for center head types. See page ALLOWABLE LOAD & MORSE TAPAR for revolutions per minute. Type KFN has the same waterproof structure as that of type KFL. Type KFN comes with the carbide center head A and then the center head ejecting drift DHN-1 (while KFN-5 comes with the carbide center head 5A60° and DHN-2). DIMENSIONS TABLE (UNIT mm) MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g) KFN-3 No.3 60 48< KC-2 KC-3 KC-4 KC-5 KC-1 KC-1 KC-6 REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.001 KC-6 (REPLACEMENT TYPE) KC-6 KCW-2 KCW-3 KCW-4 KCW-5 KCW-1 KCW-1 　KABUTO SEAL CENTER S-S KS-P KS-S KS-P KS-2Sor2P KS-3Sor3P KS-4Sor4P KS-5Sor5P KS-A KS-A  KS-3A KS-4A KS-5A KS-B KS-B KS-3B KS-4B KS-5B KS　KABUTO SEAL CENTER n. KS-S KS-P KS-S KS-P KS-2Sor2P KS-3Sor3P KS-4Sor4P KS-5Sor5P KS-A KS-A KS-3A KS-4A KS-5A KS-B KS-B KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7 KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10 KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14 KFL　KABUTO FINELIVE CENTER KFL KFL KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-A KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-B KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 KFL　KABUTO FINELIVE CENTER KFL REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003 KFL KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-A KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-B KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 KFL-3 No.3 48 30 16 36.2 33 87 4.5 22.5 156.2 REPLACEMENT 1,200 KFL-4 No.4 63 32 16 40.2 42 109 5.3 26.5 191.2 REPLACEMENT 2,100 KFL-5 No.5 85 52 26 60.5 50 136 6.3 38 246.5 REPLACEMENT 4,600 KFL-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-A   KFL-3A No.3 48 28 37 33 87 4.5 157 INTEGRAL 1,200 φ12 KFL-4A No.4 63 32 40 42 109 5.3 191 INTEGRAL 2,100 φ14 KFL-5A No.5 85 42 55 50 136 6.3 241 INTEGRAL 4,600 φ18 KFL-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFL-B KFL-3B No.3 48 25 10 41.5 33 87 4.5 161.5 INTEGRAL 1,150 φ7 KFL-4B No.4 63 32 12 52 42 109 5.3 203 INTEGRAL 2,050 φ10 KFL-5B No.5 85 42 20 65 50 136 6.3 251 INTEGRAL 4,500 φ14 KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003 KSN (g) KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KSN-A KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 KSN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KSN-B KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003 KSN KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KSN-A KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 KSN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KSN-B KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 KSN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003 KSN KSN-3 No.3 54 44 30 16 36.2 45 82 1.5 22.5 33 163.2 REPLACEMENT 950 KSN-4 No.4 69 56 32 16 36.2 57.5 104.5 1.8 22.5 43.5 198.2 REPLACEMENT 1,820 KSN-5 No.5 88 73 52 26 60.5 70 132 2.3 38 54 262.5 REPLACEMENT 4,160 KSN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KSN-A KSN-3A No.3 54 44 26 34 45 82 1.5 33 161 INTEGRAL 930 φ12 KSN-4A No.4 69 56 32 41 57.5 104.5 1.8 43.5 203 INTEGRAL 1,880 φ14 KSN-5A No.5 88 73 40 48 70 132 2.3 54 250 INTEGRAL 3,950 φ18 KSN-3B No.3 54 44 22 10 36 45 82 1.5 33 163 INTEGRAL 890 φ7 KSN-4B No.4 69 56 30 12 49 57.5 104.5 1.8 43.5 211 INTEGRAL 1,860 φ10 KSN-5B No.5 88 73 38 18 59 70 132 2.3 54 261 INTEGRAL 3,950 φ14 KFN　KABUTO FINELIVE CENTER with NUT KFN REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY 0.003 KFN KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240 KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330 KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150 KFN-A INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFN-A KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12 KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14 KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18 KFN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFN-B KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7 KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10 KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14 KFN　KABUTO FINELIVE CENTER with NUT KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240 KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330 KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150 KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12 KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14 KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18 KFN-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KFN-B KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7 KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10 KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14 KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240 KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330 KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150 3 KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12 KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14 KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7 KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10 KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14 KLN　KABUTO LATHE CENTER with NUT F L M N N1 H WEIGHT (g) KLN-3 No.3 24 16 36.1 11 87.5 6.5 22.4 134.6 M26×P1.5 41 13 21 590 KLN-4 No.4 32 16 36.2 15 112.5 10 22.5 163.7 M36×P1.5 55 22 27 1,230 KLN-5 No.5 44 26 61.2 15.5 141.5 10 38 218.2 M50×P1.5 69 20 36 2,560 KLN　KABUTO LATHE CENTER with NUT KLN REPLACEMENT TYPE WAGGLE ACCURACY 0.005 KLN KLN-3 No.3 24 16 36.1 11 87.5 6.5 22.4 134.6 M26×P1.5 41 13 21 590 KLN-4 No.4 32 16 36.2 15 112.5 10 22.5 163.7 M36×P1.5 55 22 27 1,230 KLN-5 No.5 44 26 61.2 15.5 141.5 10 38 218.2 M50×P1.5 69 20 36 2,560 KS-S KS-P REPLACEMENT TYPE WATERPROOF WAGGLE ACCURACY S TYPE 0.006 P TYPE 0.003 KS-S KS-P KS-2Sor2P No.2 37 27 15.5 36.2 30 68 4 22.5 134.2 REPLACEMENT 500 KS-3Sor3P No.3 44 30 16 36.2 42 85 4.5 22.5 163.2 REPLACEMENT 860 KS-4Sor4P No.4 56 32 16 36.2 54 108 5.3 22.5 198.2 REPLACEMENT 1,700 KS-5Sor5P No.5 73 52 26 60.5 66 136 6.3 38 262.5 REPLACEMENT 3,900 KS-3A No.3 44 26 34 42 85 4.5 161 INTEGRAL 850 φ12 KS-4A No.4 56 32 41 54 108 5.3 203 INTEGRAL 1,750 φ14 KS-5A No.5 73 40 48 66 136 6.3 250 INTEGRAL 3,650 φ18 KS-B INTEGRAL WATERPROOF WAGGLE ACCURACY 0.003 KS-B *For KS-A, B, please choose steel (tempered product) or with carbide. (UNIT mm) KS-3B No.3 44 22 10 36 42 85 4.5 163 INTEGRAL 830 φ7 KS-4B No.4 56 30 12 49 54 108 5.3 211 INTEGRAL 1,700 φ10 KS-5B No.5 73 38 18 59 66 136 6.3 261 INTEGRAL 3,650 φ14 KABUTO CLIPPER Easy-to-handle lathe optimal for grinding and machining shafts. Uses the eccentric cam. KABUTO CLIPPER Easily detachable in one hand. Not slippery as it is more firmly fastened under larger load. The finished work surface is less likely to be scratched as it is pressed in a planar manner. DIMENSIONS TABLE (UNIT mm) MODEL TYPE RANGE OF USE A B C D E G (BOLT) SPRING WEIGHT (g) #8 φ4～φ8 26 12 51 6.3 3.2 M4 P0.7×20 SMALL 40 #13 φ6～φ14 36 18 72 11 4.3 M6 P1.0×25 LARGE 100 #22 φ13～φ24 48 28 88 11 4.3 M6 P1.0×25 LARGE 130 #30 φ20～φ33 58 38 94 11 4.3 M6 P1.0×25 LARGE 160 #40 φ31～φ42 68 48 103 11 4.3 M6 P1.0×25 LARGE 190 #50S φ38～φ50 78 58 115 11 4.3 M6 P1.0×30 LARGE 250 #60S φ47～φ62 95 70 134 14 6 M8 P1.25×40 NEW OVERSIZE 450 #80S φ60～φ80 115 90 155 14 6 M8 P1.25×40 NEW OVERSIZE 540 #100 φ80～φ100 140 109 189 20 9 M10 P1.5×45 OVERSIZE 1,100 Specialty #4 φ2～φ4 22 8.5 45 6 3.2 M4 P0.7×20 SMALL - Specialty #120 φ100～φ120 164 132 209 20 9 M10 P1.5×45 OVERSIZE - *Dimensions are subject to change for alteration without prior notice.       เมนู sales@mechatronics.co.th;mmt.mechatronics@gmail.com : Mobile : K.ภูรินทร์ 098-4288648 Line ID : 0984288648 หมวดหมู่สินค้า Cabur Panasonic SRAM PC Card สำหรับ FANUC Accuvision Technology AICHI TOKEI DENKI AIR CHUCK ANSON HYDRAULICS INDUSTRIAL.,LTD. AQUA -J Oil Skimmer เจ้าหน้าที่ Admin login Sales Team login Warehouse Team login Driver Team login Service Team login Purchasing login Project Management login Contact Us Tel. ติดต่อคุณภูรินทร์ 098-4288648 Email: sales@mechatronics.co.th Fax. LINE ID : 0984288648 www.mechatronics.co.th จำนวนผู้เข้าชมเว็บไซต์ : 6,440,078 Copyright © mechatronics.co.th All Rights Reserved. ยินยอมในการเก็บรวบรวมใช้ข้อมูลส่วนบุคคลเพื่อให้สิทธิประโยชน์เฉพาะตัวแก่ผู้ใช้บริการ   อนุญาต     (รายละเอียดความยินยอม)